Contact:
Related Contents:
-
Comparison FlexRay/CAN Interfaces
Technical Data FlexCard Cyclone II SE / E-Ray VN3300 VN3600 VN7600 Number of channels 2 FlexRay 2 FlexRay 2 FlexRay 2 FlexRay/3 CAN Area of application mobile, stationary stationary mobile, stationary mobile, stationary Usage Analysis, stimulation, simulation Analysis, stimulation, simulationPC interfaces PCMCIA Type II
32 bit CardBusPCI
32 bit, 33 MHz/66 MHzUSB 2.0 USB 2.0 FlexRay communication controller (analysis) Bosch E-Ray
(Altera Cyclone II EP2C70)Bosch E-Ray
(Altera Cyclone II EP2C70)FlexRay communication controller (startup) --- Fujitsu MB88121BTransceiver Integrated (NXP TJA1080) FRpiggy (NXP TJA1080)Memory for data transmission 8 kByte 2 MBTemperature range
Operation:
Storage:
0..+60 °C
-40..+70 °C
0..+55 °C
-40..+85 °CDimensions (mm) 85 x 54 x 5,5 167 x 107 x 15 151 x 110 x 35 151 x 110 x 45 Power consumption (typ.) 1.5 W 3.2 W 3 W 4.5 W Driver library TZM FlexCard Library Vector XL-Driver-LibraryOperating system requirements Windows 2000, XP/Vista Windows XP/Vista (32 bit), Windows 7 (32 and 64 bit)Functions FlexCard Cyclone II SE / E-Ray VN3300 VN3600 VN7600 Dynamic reconfiguration of the CC buffers --- 
Transmission and reception of data and null frames Detection of invalid frames Cycle multiplexing Support of the maximum payload of 254 Byte In-cycle response Coldstart of the FlexRay cluster without additional node Hardware-based incrementing of a payload area --- Support of PDU --- Startup + asynchronous monitoring Time synchronization
with synchronization cable
without synchronization cable
---
Trigger input and output Low PC loading due to DMA (Direct Memory Access) --- Very short latency period --- --- --- - Bus Transceiver
- Accessories
- Drivers & Libraries
- Downloads
VN7600 – USB Interface for FlexRay and CAN
Great Versatility: The USB Interface for FlexRay and CAN
| Technical Data | |
|---|---|
| Area of application | Analysis, stimulation, simulation |
| Usage | Mobile and stationary |
| Microcontroller | Intel PXA270 (312 MHz) |
| RAM | 8 MB |
| FlexRay communication controller (analysis) | Bosch E-Ray (Altera Cyclone II EP2C70) |
| FlexRay communication controller (startup) |
Fujitsu MB88121B |
| Memory for data transmission | 2 MB |
| FlexRay cluster | 1 |
| FlexRay channels/connection | 2 (channel A and B of a cluster); 1 x D-SUB9 (male) |
| CAN channels/connection | 3 independent channels, 3x D-SUB9 (male) |
| Maximum payload | 254 Bytes |
| Transceiver | FRpiggy 1080 or FRpiggy 1080 mag (NXP TJA1080) and CANpiggies (see bus transceiver data sheet) |
| PC Interface | USB 2.0 |
| Temperature range | Operation: 0..+55 °C 1 Storage: -40..+85 °C |
| External power supply | 6 V..50 V, startup at 8 V |
| Power consumption (typical) | 4.5 W |
| Dimensions (LxWxH) | 151 x 110 x 45 mm |
| Operating system | Windows XP/Vista (32 bit), Windows 7 (32 and 64 bit) |
| Driver Library | XL-Driver-Library |
1 Extended temperature range -20..+70°C (tested but not guaranteed)
Did you find this page helpful?